MAXTECH CORPORATION XPVS 56E (SF-1156V/T3(x2)) Card Type Modem, Fax Chip Set Unidentified I/O Options Microphone in, speaker out, line in, line out, DC power, serial port Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A, V.22, V.22bis, V.23, V.32, V.32bis, V.34+, x2 Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42bis Fax Class Class I & II Data Bus External [Image] CONNECTIONS Function Label Function Label Line in CN1 Microphone in CN5 Line out CN2 Speaker CN6 Serial port CN3 Volume R1 DC power CN4 Power switch SW1 DIAGNOSTIC LED(S) LED Color Status Condition ARQ Unidentified On MNP or V.42 connection is established ARQ Unidentified Blinking Data is re-sent ARQ Unidentified Off No connection established AA Unidentified On Auto-answer enabled AA Unidentified Blinking Phone is ringing AA Unidentified Off No line activity present CD Unidentified On Carrier signal detected CD Unidentified Off Carrier signal not detected OH Unidentified On Modem has gone off hook OH Unidentified Off Modem is on hook RD Unidentified On Data is being sent to the computer through the modem RD Unidentified Off No data is being sent SD Unidentified On Modem is receiving data from the computer SD Unidentified Off Modem is not receiving data from the computer TR Unidentified On Modem can receive commands TR Unidentified Off Modem cannot receive commands MR Unidentified On The modem is turned on MR Unidentified Off The modem is turned off SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, B, E, F, H, M, O, P, T, V, X &C, &G, &T, &W, &Z S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25 Special Commands #BDR, #CLS, #CID, #MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX, +MS, +MS? Note: See MHI Help File for full command documentation. Proprietary AT Command Set ACTIVE/DEFAULT PROFILE CONFIGURATION Type: Immediate Format: AT [cmds] Zn [cmds] Description: Determines which profile the modem should use upon power-up or reset. Command Function Z0 Reset and retrieve the profile set by the ‘Y’ command Z1 Reset and retrieve active Profile 0 Z2 Reset and retrieve active Profile 1 Z3 Reset and retrieve default Profile 0 Z4 Reset and retrieve default Profile 1 Z5 Reset and retrieve default Profile 2 ANSWER MODE Type: Configuration Format: AT [cmds] Bn [cmds] Description: Configures modem to either answer in U.S. answer mode or V.25 answer mode. Command Function B0 Sets modem for ITU-T V.25 answer mode B1 Sets modem for U.S. answer mode AUTOMATIC REPEAT REQUEST Type: Configuration Format: AT [cmds] &An [cmds] Description: Configures ARQ result codes, V.32, error correction, and compression protocols Command Function &A0 ARQ result codes disabled &A1 ARQ result codes enabled &A2 ARQ result codes and V.32 enabled í &A3 ARQ result codes, V.32, error correction, and data compression enabled BREAK CONFIGURATION Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Configures Line Break Command Function &Y0 Destructive break / Does not send break &Y1 Destructive break / Break expedited &Y2 Non-destructive break / Break expedited COMMAND SET Type: Immediate Format: AT [cmds] $ [cmds] Description: Displays modem command sets &$ Displays the ampersand command set COMMUNICATIONS MODE (ASYNCHRONOUS) Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Set to normal mode &M4 Enable ARQ and normal modes &M5 Only enables ARQ mode CONNECTION SPEED Type: Configuration Format: AT [cmds] &Nn [cmds] Description: Configures modem connection speed Command Function &N0 Automode enabled &N1 Connection speed set to 300bps &N2 Connection speed set to 1200bps &N3 Connection speed set to 2400bps &N4 Connection speed set to 4800bps &N5 Connection speed set to 7200bps &N6 Connection speed set to 9600bps &N7 Connection speed set to 12Kbps &N8 Connection speed set to 14.4Kbps &N9 Connection speed set to 16.8Kbps &N10 Connection speed set to 19.2Kbps &N11 Connection speed set to 21.6Kbps &N12 Connection speed set to 24Kbps &N13 Connection speed set to 26.4Kbps &N14 Connection speed set to 28.8Kbps &N15 Connection speed set to 31.2Kbps &N16 Connection speed set to 33.6Kbps &N17 Connection speed set to 33.333Kbps &N18 Connection speed set to 37.333Kbps &N19 Connection speed set to 41.333Kbps &N20 Connection speed set to 42.666Kbps &N21 Connection speed set to 44Kbps &N22 Connection speed set to 45.333Kbps &N23 Connection speed set to 46.666Kbps &N24 Connection speed set to 48Kbps &N25 Connection speed set to 49.333Kbps &N26 Connection speed set to 50.666Kbps &N27 Connection speed set to 52Kbps &N28 Connection speed set to 53.333Kbps &N29 Connection speed set to 54.666Kbps &N30 Connection speed set to 56Kbps &N31 Connection speed set to 57.333Kbps DATA COMPRESSION Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enable/disable Auto Data, V.42bis, and MNP5 compression Command Function &K0 V.42bis and MNP5 compression disabled í &K1 Auto Data compression enabled &K2 V.42bis and MNP5 compression enabled &K3 MNP5 compression disabled DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR is off while in command mode and set on in on-line mode DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. DCE CONNECTION SPEED Type: Configuration Format: AT [cmds] &Un [cmds] Description: Configures DCE modem connection speed Command Function &U0 Variable DCE connection speed enabled &U1 Connection speed set to 300bps &U2 Connection speed set to 1200bps &U3 Connection speed set to 2400bps &U4 Connection speed set to 4800bps &U5 Connection speed set to 7200bps &U6 Connection speed set to 9600bps &U7 Connection speed set to 12Kbps &U8 Connection speed set to 14.4Kbps &U9 Connection speed set to 16.8Kbps &U10 Connection speed set to 19.2Kbps &U11 Connection speed set to 21.6Kbps &U12 Connection speed set to 24Kbps &U13 Connection speed set to 26.4Kbps &U14 Connection speed set to 28.8Kbps &U15 Connection speed set to 31.2Kbps &U16 Connection speed set to 33.6Kbps &U17 Connection speed set to 33.333Kbps &U18 Connection speed set to 37.333Kbps &U19 Connection speed set to 41.333Kbps &U20 Connection speed set to 42.666Kbps &U21 Connection speed set to 44Kbps &U22 Connection speed set to 45.333Kbps &U23 Connection speed set to 46.666Kbps &U24 Connection speed set to 48Kbps &U25 Connection speed set to 49.333Kbps &U26 Connection speed set to 50.666Kbps &U27 Connection speed set to 52Kbps &U28 Connection speed set to 53.333Kbps &U29 Connection speed set to 54.666Kbps &U30 Connection speed set to 56Kbps &U31 Connection speed set to 57.333Kbps DCE/DTE Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Adjust DCE/DTE rate settings Command Function &B0 DTE follows DCE í &B1 DTE constant &B2 DTE constant in ARQ mode and a variable rate in non-ARQ mode DIAL MODE Type: Configuration Format: AT [cmds] Dn [cmds] Description: Configures the dialing mode the modem will use. Command Function DL Redials last number DP Uses pulse dialing DS=n Dial number in stored memory DR Reverses the dial mode í DT Uses touch-tone dialing DW Waits for two dial tones D, Pause D; Modem returns to &Dmode after dialing D/ Uses a 125 msec delay before dialing D! Uses flash D@ Set to wait for 5 seconds of line silence D$ Displays the dialing commands ECHO COMMANDS Type: Configuration Format: AT [cmds] En [cmds] Description: Configures modem to either echo commands or not to echo commands Command Function E0 Local echo enabled í E1 Local echo disabled FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore default configuration 0 í &F1 Restore default configuration 1 (enables hardware flow control) &F2 Restore default configuration 2 (enables software flow control) MODEM RESPONSE Type: Configuration Format: AT [cmds] Qn [cmds] Description: Determines when and how the modem sends reponses Command Function í Q0 Result code sending enabled Q1 Result code sending disabled Q2 Displays result codes when modem is set in Originate mode PROFILE CONFIGURATION Type: Immediate Format: AT [cmds] Yn [cmds] Description: Determines which profile the modem should use upon power-up or reset. Command Function Y0 Set Profile 0 active upon power-up or reset Y1 Set profile 1 active upon power-up or reset PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe and Hong Kong) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product identification code I1 Reports ROM checksum I2 Reports internal memory test I3 Reports product identification I4 Reports current modem settings I5 Reports active and stored profiles I6 Reports link diagnostics I7 Reports modem configuration RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 Reserved &R1 CTS forced high, RTS is ignored. &R2 RX hardware flow control enabled RX FLOW CONTROL Type: Configuration Format: AT [cmds] &In [cmds] Description: Configure RX & ENQ/ACK flow control settings (XON/XOFF) Command Function í &I0 Software RX flow control disabled &I1 Software RX flow control enabled &I2 RX flow control enabled without passthrough &I3 ENQ/ACK flow control enabled in host mode &I4 ENQ/ACK flow control enabled in terminal mode &I5 Software RX flow control enabled for non-ARQ mode SPEAKER VOLUME Type: Immediate Format: AT [cmds] Ln [cmds] Description: Controls the volume of the modem speaker Command Function L0 Low volume setting L1 Low volume setting í L2 Medium volume setting L3 High volume setting Description: Controls 8S-2D, 16S-4D, 32S-2D, and 64S-4D trellis coding. TX FLOW CONTROL Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Configure TX flow control settings (XON/XOFF) Command Function &H0 CTS flow control disabled í &H1 CTS flow control enabled &H2 Software flow control enabled &H3 Software flow control and CTS enabled S(status) -Registers BIT-MAPPED REGISTER S13 Format: AT [cmds] S13=n [cmds] Default: 0 Unit: Bit-mapped Description: Controls RX flow control, buffer reset, backspace, autodial, retrain, and hang-up commands. BIT-MAPPED REGISTER S27 Format AT [cmds] S27=n [cmds] Default: 0 Unit: Bit-mapped Description: Controls V.21, V.23, V.32, V.32bis, trellis coding, answer tone, and 9600bps result codes. BREAK LENGTH Format AT [cmds] S21 [cmds] Default: 10 Range: 0-255 Unit: .01 second Description: Determines the break length COMPRESSION CONFIGURATION Format AT [cmds] S15 [cmds] Default: 0 Range: Unidentified Unit: Bit-mapped register Description: Disable ARQ/MNP/V.42bis compression COMPRESSION PROTOCOLS Type: Register Format: AT [cmds] S32=n [cmds] Default: 2 Unit: Bit-mapped register Description: Controls V.8, V.34, V.34bis, and x2 compression protocols DIAL LINE RATE Type: Register Format AT [cmds] S38=n [cmds] Default: 0 Range: 0 - 19 Unit: Unidentified Description: Sets the 56K dialing rate DISTINCTIVE RING Format AT [cmds] S41 [cmds] Default: 0 Range: 0-1 Unit: Bit-mapped register Description: Enables or disables the distinctive ring function on the modem DTR HANG-UP DELAY Type: Register Format AT [cmds] S38=n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Controls the DTR hang-up delay time FLOW CONTROL CHARACTER - XON Format AT [cmds] S22 [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON FLOW CONTROL CHARACTER - XOFF Format AT [cmds] S23 [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF INACTIVITY TIMER Format AT [cmds] S19 [cmds] Default: 0 Range: 0-255 Unit: minutes Description: Disconnects line connection after a certain period of line inactivity SYMBOL RATES Type: Register Format: AT [cmds] S33=n [cmds] Default: 0 Unit: Bit-mapped register Description: Controls 2400, 2743, 2800, 3000, 3200, and 3429 symbol rates. TRELLIS CODING Type: Register Format: AT [cmds] S34=n [cmds] Default: 0 Unit: Bit-mapped register V.21 ANSWER MODE TIMER Type: Register Format AT [cmds] S29=n [cmds] Default: 20 Range: 0-255 Unit: .01 second Description: Time the modem will go on-hook upon receiving the ! dial modifier in dial string. V.32 ANSWER TONE Format AT [cmds] S28=n [cmds] Default: 8 Range: 0-255 Unit: .1 seconds Description: Controls V.32 answer tone